Supply Chain - Reservoirs & Storage - Precast Concrete Storage Tanks
3
results
Related Content
Case Studies
- Isle of Wight South Strategic Optimisation (2023)
- Lower Barden Reservoir (2023)
- Whitehall Distribution Service Reservoir (2023)
- Clough Bottom Impounding Reservoir (2023)
- Mosswood WTW (2024)
- Llyn Bran Discontinuance (2023)
- Springwell Service Reservoir (2024)
- Dunside Reservoirs (2024)
- Tunstall Reservoir (2024)
- Toplers Hill Water Tower (2024)
- Birds Park Impounding Reservoir (2023)
- Lluest Wen Reservoir (2023)
Figure 2: The planning process developed - Courtesy of Southern Water[/caption]
Figure 3: Typical Pareto curve showing best performing plans - Courtesy of Southern Water[/caption]
Incorporating environmental performance into the optimisation was a particular challenge. The team approached this by taking the results from a high level environmental feasibility assessment and factoring in WSR and pipe costs proportionally to reflect better and worse performing options. This then carried through into the overall cost/performance results for that plan.
In the example, the Pareto curve shows about 216 OptimizerTM plans (from 30,000) from which 10 plans have been identified as feasible options.
The OptimizerTM tool is very powerful at testing several configurations (plans) based on the given inputs, design criteria and formulations. Review and validation are critical parts of the process, and this involves the team checking outputs (individual plan performance), tweaking inputs (adjusting costs/penalties/formulations) and refining the optimisation until several tangible plans are derived.
Figure 4 shows typical age of water results for several WSRs with shortlisted plan 7639, 8142 & 8041 compared against the existing system performance. This demonstrates how the optimised plans can significantly reduce the age of water meeting one of the projects key objectives.
[caption id="" align="alignnone" width="1200"]
Figure 4: Age of water optimisation - Courtesy of Southern Water[/caption]
The original spillway channel - Courtesy of MMB[/caption]
Completed masonry cladding on spillway, and (inset) wall raising showing new and existing masonry - Courtesy of MMB[/caption]
Upstream leg of siphon - Courtesy of MMB[/caption]
Due to the levels of communication between Stantec and MMB, this additional chamber was designed out and the chamber was moved into the stilling basin, prior to it being backfilled to contain the spillway flows. This reduced additional excavation works and aided in the construction programme, promoting some carbon efficiencies. Good communication between both parties ensured that both projects were capable of being delivered within programme and reduced abortive works.
Fibre reinforced concrete tumble bay slab - Courtesy of MMB[/caption]
The site team and stone masons chosen for the scheme comprised of the majority of those who had worked on the previously delivered Swinsty Spillway structure and had an in-depth working knowledge of constructing these structures. Their knowledge and experience greatly aided with the construction of the scheme and achieving the challenging programme.
The siphon works required a significant draw down of the reservoir level to be able to work on the inlet structure safely. As this was quite a long duration for the works, it would impact the programme significantly and equally impact the spillway structure. It was decided to work from both ends of the pipe where practicable and to use a make-up piece at a bend on the downstream side of the embankment. This would aid in any minor tolerance issues in the pipework and ensure that the pipe closed correctly.
To aid the construction of the pipework, the ICON system was used for setting out. This involved directly using the 3D modelling from the design of the pipe into a handheld tablet device and enabled accurate setting out, without the need to update drawings or continually check that the drawings were the most relevant. This also aided in delivering the as built positions of the pipework for the updates to the completion drawings.
[caption id="" align="alignnone" width="1200"]
3D model showing the interaction between the spillway and siphon schemes - Courtesy of MMB[/caption]
Manufacturing the tanks off-site - Courtesy of ESD[/caption]
Delivery to site - Courtesy of ESD[/caption]
(left) The new wave wall upon completion, (top right) construction of the wavewall and, (bottom right) construction work on the spillway - Courtesy of Costain[/caption]
Field where the lagoon will be sited - Courtesy of Mott MacDonald Bentley[/caption]
Early construction of the lagoon - Courtesy of Mott MacDonald Bentley[/caption]
Lagoon liner installation - Courtesy of Mott MacDonald Bentley[/caption]
Security gate installed to allow access to lagoon area - Courtesy of MMB[/caption]
Llyn Bran before discontinuance - Courtesy of Welsh Water[/caption]
Llyn Anafon is nationally and internationally protected for specific conservation features. This means prior to any project taking place, a full Habitats Regulation Assessment (HRA) had to be undertaken. The outcome of this assessment was that it was not possible to avoid adverse impacts to protected features and as such, the only route to proceed with the project was under the “Imperative Reasons of Overriding Public Interest (IROPI)” (Article 6.4 of the Habitats Directive) on the grounds of public safety. The Anafon Dam Discontinuance Scheme is the first IROPI case of its kind in the UK and has recently been approved by Welsh Government.
To satisfy the IROPI case, Welsh Water was required to secure ‘compensatory measures’ for the loss of habitat at Anafon. Using a set of criteria agreed with National Resources Wales (NRW), Llyn Bran was identified as the most suitable site to provide the necessary compensation. A key element of the work was to ‘restore and maintain hydrological functioning’ i.e., removal of the dam to create a natural lake and restore connectivity to the downstream watercourse.
Although the primary reason for discontinuing Llyn Bran was for compensation, it also had the added benefit of removing a dam which was no longer needed for operational purposes.
[caption id="" align="alignnone" width="1200"]
Llyn Bran dam before discontinuance - Courtesy of Welsh Water[/caption]
Ground conditions - Courtesy of Welsh Water[/caption]
As with all discontinuance schemes the various surveys, permits, consents and negotiations in advance of the physical works were particularly complex, taking more than two years to complete. An overview of the consents and constraints required is below:
(left) Bog mat access track and (right) amphibious excavator used to load barge with coir matting - Courtesy of Welsh Water[/caption]
Peat
The extent of peat encountered on site was far greater than expected once construction began. This resulted in an entire change in the contractors methodology for the coir matting. It was initially planned to use Bog Master excavator and tracked dumper to access the western shore of the reservoir, however it quickly became clear this was not practical. Thanks to the contractor being proactive, the methodology was quickly changed to using an amphibious excavator and barge, to transport the coir matting across the reservoir.
Water voles
Water voles were identified on site during the early site survey stages, meaning a licence was required to temporarily remove the voles during construction.
Six water voles were captured by specialists and were transferred to a facility in Kent, where they were looked after while the work took place. A condition of the licence was that there must be 5-days with no water voles captured before it could be concluded that all voles were removed from site. Rather unluckily, there were two occasions where a vole was captured at the end of the fifth day, meaning the process took far longer than expected and the licence had to be extended. The voles are due to return home to Llyn Bran this summer.
[caption id="" align="alignnone" width="1200"]
Water voles were captured and transferred to a facility in Kent for the duration of the works - Courtesy of Welsh Water[/caption]
Compensation flow
A condition of the NRW impoundment licence was for a continuous compensation flow of at least 20 l/s for the duration of the works. This meant pumping to the watercourse, which had to be continually monitored. It was hoped to use a cloud-based telematics tool that makes it easy to monitor the pumps off-site but unfortunately, due to lack of signal, this did not work meaning William Hughes Civil Engineering needed to attend site over the weekends to check on the compensation flows. The summer of 2022 proved to be exceptionally dry, which crated a challenge in meeting compensation flows whist also not allowing the remaining lake to become too low.
Flood risk
The existing reservoir provided significant flood attenuation meaning the discontinuance increased the flood risk to a downstream highway culvert. Initially, there were concerns from the highways department that the culvert would need to be upsized, which would have added significant costs to the project. Following a detailed flood risk and stability assessment, Welsh Water were able to prove that the increased flood risk would not adversely affect the culvert and only minimal slope protection work around the culvert was required.
[caption id="" align="alignnone" width="1200"]
Amphibious excavator forming the new channel connecting to the downstream watercourse - Courtesy of Welsh Water[/caption]
Cores being drilled through concrete dam to allow any extreme storm flows to pass through - Courtesy of Welsh Water[/caption]
Dam safety mitigation
During detailed design, the Dam Safety Team suggested coring holes though the concrete dam once the reservoir was drawn down to the required level. This would mitigate the risk of the reservoir refilling during severe weather, before the dam was fully demolished. Fortunately, on this occasion the weather was favourable and the cores were not needed. This approach will be considered for any future concrete dam discontinuances.
Waste removal
It was agreed with NRW that the stone from the haul road and compound could be transferred to a nearby quarry, just down the road from site. This was done under a waste transfer notice, saving costs. The arisings from the dam were removed off site. The dam was demolished far easier and quicker than expected, making the removal of concrete straightforward.
[caption id="" align="alignnone" width="1200"]
Dam demolition in progress - Courtesy of Welsh Water[/caption]
Coir matting
Due to the silt being drier than anticipated, there was spare rolls of coir matting left over. Rather than this being wasted, it was moved to nearby Alwen WTW where it is being stored before being used for silt management on the upcoming Cilcain Discontinuance Scheme which is due to start this spring.
Springwell Service Reservoir 3D model - Courtesy of MMB[/caption]
Springwell Reservoir base construction - Courtesy of MMB[/caption]
Springwell valve house - Courtesy of MMB[/caption]
Springwell settlement bund - Courtesy of MMB[/caption]
(left) Wall panels and (right) wall infills - Courtesy of MMB[/caption]
Springwell Reservoir under construction - Courtesy of MMB[/caption]
Springwell Reservoir columns and roof - Courtesy of MMB[/caption]
Dunside Reservoirs prior to breach - Courtesy of George Leslie Ltd[/caption]
Water management plan layout - Courtesy of George Leslie Ltd[/caption]
(left) Dunside Reservoirs during construction July 2023, and (right) after breach - Courtesy of George Leslie Ltd[/caption]
Reinstatement of the watercourse - Courtesy of George Leslie Ltd[/caption]
(left) Condition of the spillway blocks prior to the works and (right) new concrete slab with stainless steel protection to the joint - Courtesy of Esh-Stantec[/caption]
Tunstall Reservoir dam - Courtesy of Esh-Stantec[/caption]
Tunstall Reservoir spillway - Courtesy of Esh-Stantec[/caption]
(left) View in the unlined section of the tunnel (notice the beams across the soffit) and (right) view of pipe inlet and partial headwall (notice standing water on the invert) - Courtesy of Esh-Stantec and CC Informatics[/caption]
Various options were considered during the Concept stage. The option of not filling the tunnel was disregarded as it would not eliminate the potential risk to the integrity of the dam embankment and spillway channel. Filling the entire extent of the tunnel was considered, however it was not preferred due to the significant constraints associated with it. These constraints include the difficult access and requirement to work in a confined space, potential land ownership issues, the presence of a SSSI immediately to the east of the abutment, and the increasing depth to the tunnel as it continues beyond the spillway. For all of these reasons, it was agreed with that filling the extent of tunnel beneath the dam and spillway would be sufficient as that would eliminate the risk to these structures.
(left) View of the geopolymer in the tunnel, and (right) view of the pea gravel stop end - Courtesy of Esh-Stantec and CC Informatics[/caption]
Overview of the siphon diversion route in preparation for the works - Courtesy of Esh-Stantec[/caption]
Toplers Hill Water Tower - Courtesy of @one Alliance[/caption]
New roof ready to be lifted - Courtesy of @one Alliance[/caption]
The new roof being lifted into place - Courtesy of @one Alliance[/caption]
Site compound across undulating glacial topography - Courtesy of Eric Wright Civil Engineering[/caption]
Bulk bag bund to inlet structure and excavation of notch - Courtesy of Eric Wright Civil Engineering[/caption]
During excavation for the spillway, rockhead was encountered at or above formation which meant that the planned sheet piled excavation through the crest was not feasible. After collaborative discussions to review risks to the embankment, an agreement was made to excavate a wide battered notch through the crest. The excavation was blinded with concrete and this innovative semi-permanent structure acted as a channel to manage flood risk prior to completion of the upstream and downstream works.
The main overflow structure and weir, to be constructed within the reservoir basin, proved extremely problematic. The concept construction method for the structure was to build a granular stone working platform into the basin and install a cofferdam to reduce environmental impact. The presence of a 2m thick layer of silt necessitating a redesign.
Following discussions with the Environment Agency, an aquatic survey was carried out and consent obtained to fully drawdown the reservoir. An impounding bund was formed using bulk bags which enabled safe isolation of the working area, allowing 200m3 of silt to be removed and replaced with dry lean compacted concrete to bring levels up to the structure formation to facilitate construction of the outlet structure.
Spillway construction in progress - Courtesy of Eric Wright Civil Engineering[/caption]
Aerial view of completed spillway with basin refilled and footpath reopened - Courtesy of Eric Wright Civil Engineering[/caption]
The project adopted a pragmatic approach to the work by client, contractor, designer, and the Reservoir Qualified Civil Engineer which, given the limited ground information, challenging timescales, and the need to adapt to ongoing investigation as works progressed, was vital to the success of the project.
The highly professional team effort delivered a technically demanding project in exceptional circumstances. Efficient delivery of quality data using innovative and bespoke solutions meant that it was still possible to complete a major capital project whilst adapting to a changing environment.
A high level of site support and a collaborative approach to problem solving, using pragmatism and engineering judgement, delivered simple, effective solutions to problems that might otherwise have been overcomplicated.
(left) Base concrete pour and (right) the upper spillway - Courtesy of MMB[/caption]
Armourstone and lower spillway - Courtesy of MMB[/caption]
Finished spillway - Courtesy of MMB[/caption]
Mini CS & Company News
- Major Supply Grid Upgrades, Somerset
Major Supply Grid Upgrades, SomersetScope of works
Excavation works began in 2017 at the Dancing Hill Reservoir site as part of a £6 million project to upgrade the Water Supply GRID for Bridgwater and the surrounding areas. Major upgrades are required due to large-scale developments in the area.Issues & solutions
The design was particularly challenging due to the complicated nature of the ground surrounding the reservoir tank. A sizeable berm was built on the ground profile around Cofferdam 4 to ensure a safe and stable excavation. This exaction also had to accept other loadings from Cofferdams 1, 2 and 3. Multiple 203UC tank brace frames were used due to the strict lift plan limit of 1 tonne. Larger or heavier brace systems could risk the collapse of existing foundations. Vibration pile driving was not permitted due to the detrimental effect it could have on the high-pressure water mains that supplies customers. There was also a HV cable running through the site that had to be avoided. The exact location of other services created additional challenges and ongoing surveys had to be monitored throughout the duration of works. As of 2017 there are four connected cofferdams in place allowing safe working space to combine new pipeworks to the main reservoir tank. Multiple back-to-back 203UC tank braces with special alignment of bracing has been key in the design, combined with KKD 600 sheets to secure the trench. Several Lightweight DavitSafe systems allow safe access into the 10m deep cofferdams.- Sector: Water & Utilities
- Client: Wessex Water
- Location: Bridgewater, Somerset
- Scheme: Water Supply GRID Upgrade
- MGF depot: Bristol
- Products hired: Multiple 203UC brace, KKD 600 sheets, lightweight davit
Dancing Hill - Courtesy of MGF Ltd[/caption]
For more information: MGF Ltd | +44 (0)1942 402700 | www.mgf.co.uk
- Kent Reservoir - South East Water
Kent Reservoir - South East WaterThe challenge
The reservoir had an estimated 180 meters of cracks that needed repair, as well as the main element of the concrete that required coating to waterproof and add durability to the concrete structure. The reservoir was taken out of commission but it needed to be returned to service as soon as possible. To do this, we looked at the order of the processes to ensure the tight time frames could be met.The Xypex Solution
In accordance with the Reg. 31 IFU (Instructions For Use) all cracks were broken out to a minimum depth of 37mm and a width of 25mm. The walls were prepared by removing the laitance and the whole area was saturated. To stem the ingress of water, every crack that showed moisture was sealed with Xypex Patch’n Plug which sets in seconds stemming the flow. To meet the required time frame, the Xypex Concentrate coating work was then undertaken to allow it to air cure for the specified time. Once applied, the crystalline technology takes time to migrate deep into the concrete and become fixed within the concrete matrix as a permanent solution. When the curing is complete the coating could be removed if required, in this instance it remained. During the curing process of the coating, the crack repairs were then filled using Xypex Concentrate as a Dry Pack and then finally topped off with a thin layer of Xypex Patch’n Plug to enable the fast return to service. [caption id="" align="alignnone" width="1200"]
The Xypex solution; Concentrate and Patch'n Plug - Courtesy of SMR Projects Ltd - Xypex UK Distributors[/caption]
The results
The allowed time frame meant undertaking the processes out of the normal sequence, but this allowed the repairs to be to be delivered on time. The coating was undertaken to increase the durability but also to pick up any minor unidentified cracks. The larger cracks were repaired and sealed using the standard Xypex repair methodology, however ultimately over 300 metres of crack repairs were completed.
For more information: SMR Projects Ltd - XYPEX UK Distributors: +44 (0)1295 279747 | www.smrxypex.co.uk
- College Avenue Contact Tank
College Avenue Contact TankThe challenge
The South East Water contact tank has a constant output of 18.1 million litres per day, it contains water which is treated with Sodium Tripolyphosphate and sodium hypochlorite before entering the distribution network. The structure is of a ‘certain’ age and has a number of active leaks that have progressively worsened over time. As the tank is in constant use, it cannot be taken off-line and so a solution was required which could be undertaken against heavy flow of water with the tank still in use.The Xypex solution
Xypex not only likes water, but the repair method requires a wet environment therefore an active leaking tank is not a problem. The cracks were chased out in accordance with the DWI Reg. 31 approved Instructions for Use Document i.e. a minimum of 37mm depth and 25mm wide, following the line of the crack. Either side of the crack was cleaned and the laitance removed to expose the capillary and pore network. [caption id="" align="alignnone" width="1200"] The Xypex solution; Concentrate and Patch'n Plug - Courtesy of SMR Projects Ltd - Xypex UK Distributors[/caption]
A bleed pipe was installed and secured with Xypex Patch’n Plug at the lowest point of the crack where water flow was at its greatest. Then the base of the crack was plugged using Xypex Patch’n Plug to stop the flow of water. This was then left to see if there were any additional issues that manifested themselves over night. Once the flow was proven to have stopped, the repair was finished using Xypex Concentrate both as a dry pack and a slurry in line with the IFU and Xypex’s standard repair methodology.
The results
The Xypex methodology using Xypex Patch’n Plug stopped the flow of water instantly and allowed the repair to be undertaken. The crystalline chemistry within the Xypex Concentrate will migrate deep in to the concrete matrix around the repair, driving water out and increasing the life and durability of the tank in those areas. [caption id="" align="alignnone" width="1200"]
Courtesy of SMR Projects Ltd - Xypex UK Distributors[/caption]
As the original repairs were undertaken, additional pressure was transferred to other cracks that were visible, but not leaking, and these were all repaired using the same method.
In all, only 2 materials were used on site and no specialist methods were used. SMR Projects Ltd attended and were on hand for technical help throughout the installation.
For more information: SMR Projects Ltd - XYPEX UK Distributors: +44 (0)1295 279747 | www.smrxypex.co.uk
Jobs
- Senior Civil Engineer - Water (6286)
Senior Civil Engineer - Water (6286)The opportunity
Across the entire business, Stantec are building on top of what’s already been a highly successful period of growth. Our strategy within the Water division for 2023 and beyond is creating a number of new exciting opportunities across the business. We partner with the top water clients across the UK, work on some of the largest, most iconic water projects in the industry and we promise to design with community in mind by reducing environmental impacts and improving social impacts. We enable the delivery of sustainable development and infrastructure projects that adapt to and mitigate the effects of climate change. Our Civil Engineers work across the project lifecycle in asset planning / strategy, concept design, outline design and detailed design. We work in a variety of project areas within the water sector, including clean water treatment and networks, wastewater treatment, wastewater networks, flooding, and urban drainage. You can find out more about our work in the water sector here: Stantec H2O+U - UK. You’ll be responsible for the project’s civil engineering design, the leadership of civil engineering teams and will work alongside our overall project design leads to ensure successful project delivery and outcomes for our clients. You will also have access to Stantec’s world-class expertise to help you deliver cutting edge design.About You
You’ll have experience working as a Civil Engineer on projects within sectors such as the water, environment or other related infrastructure sectors. Ideally you will hold Chartered or Incorporated member status with a relevant professional body such as ICE or CIWEM. You’ll have a passion for the water and environment sector and supporting our developing civil engineers. You’ll also be experienced in successful project delivery and working collaboratively with project teams to develop innovative solutions. Finally, you will have experience of working in a client facing role, leading client engagement and collaboration on a regular basis.
About Stantec
The Stantec community unites more than 31,000 employees working in over 450 locations across 6 continents. We have been working with our clients and communities in the UK for over 150 years. We plan, design, deliver and manage the development and infrastructure needed to support the creation of sustainable, healthy and prosperous communities. Our teams provide effective and relevant solutions, translating our clients’ vision into valued consents, deliverable plans for projects and programmes, and efficient designs for delivery, based on technical excellence and deep market insights. We deal with today’s challenges, but also keep a fairer, better tomorrow in sight, looking at how we deliver clean growth, support radical changes in our economy and meet the needs of future communities. Stantec provides equal employment opportunities to all qualified employees and applicants for future and current employment and prohibit discrimination on the grounds of race, colour, religion, sex, national origin, age, marital status, genetic information, disability, sexual orientation, gender identity or gender expression. We prohibit discrimination in decisions concerning recruitment, hiring, referral, promotion, compensation, fringe benefits, job training, terminations or any other condition of employment. Stantec is in compliance with laws and regulations and ensures equitable opportunities in all aspects of employment. Building an inspired, inclusive work environment that attracts, supports, and develops world-class talent is a crucial key to our success. If you are excited by this role but worry that your experience doesn’t exactly align, we encourage you to apply. - Civil Engineer - Water (6331)
Civil Engineer - Water (6331)
The opportunity
Do you have a passion for Civil Engineering ? Are you driven to create solutions for the unprecedented climate, environmental, and efficiency challenges facing our clients and the wider community? Then make a real difference and join us at Stantec! We are excited to continue our growth journey in Ireland and Northern Ireland and we have exciting plans for expansion in 2025 and beyond. We look forward to continuing our work with Uisce Eireann on the Engineering Design Services Framework and in Northern Ireland, we are proud to have been appointed to Northern Ireland Water’s IF182 Professional Services Framework. Taoiseach Simon Harris recently opened our new Dublin office, and we have now also moved to a new city center office in Belfast. This exciting pipeline of work, coupled with the scale of opportunity across the AMP8 cycle in the UK means that we seeking Civil Engineers at all levels with experience in the water/wastewater industry to join us. We are flexible with location so the position can be based in Dublin, Belfast or elsewhere. You will have the opportunity to join a dynamic team spread across the UK and Ireland, supporting the delivery of a variety of projects as part of a major capital investment programme.You will play an important role in the team, developing technical solutions & providing advice to our clients. You will provide technical expertise to ensure projects are delivered to cost, schedule & quality standards and work collaboratively amongst multi-disciplinary teams to ensure first class delivery of our projects. You will work closely with external stakeholders & clients to develop long term relationships.About You
You will be Degree qualified (or equivalent) in Civil Engineering or other relevant subject and have some experience of working within the regulated water industry.You will have knowledge of water and wastewater infrastructure/networks and treatment. Due to the nature of upcoming projects, ideally, you will also have experience in areas such as Clean Water and Wastewater Treatment, Trunk Mains and Large Diameter Pipeline Design.Ideally, you’ll have previous consultancy experience in a design role.Most importantly, you’ll embody our values and ethos of client focus and service excellence and have a passion for making a difference in the Water sector.Why Join us?
- Our People Culture: We're a close knit team and very proud of our friendly and collaborative environment
- Growth: We're on an exciting growth journey in Ireland and Northern Ireland - we want you to be part of it!
- Awards: Stantec were awarded the International Consulting Firm of the Year and Best place to work - Large Consulting Firms at the 2024 NCE awards as well as being consistently recognised in the top 10 Corporate Knights most sustainable companies in the world.
- Great Benefits: Competitive salary, pension plan, holidays, free private medical insurance, discounted gym membership and lots more.
- Flexible working arrangements
- Great Projects: We have secured positions on both the Uisce Eireann and NI Water Frameworks and are delivering a wide variety of projects that will make a real difference to our communities
- Industry leading training and development as well as paid for professional subscriptions
About Stantec
The Stantec community unites more than 31,000 employees working in over 450 locations across 6 continents. We have been working with our clients and communities in the UK for over 150 years. We plan, design, deliver and manage the development and infrastructure needed to support the creation of sustainable, healthy and prosperous communities. Our teams provide effective and relevant solutions, translating our clients’ vision into valued consents, deliverable plans for projects and programmes, and efficient designs for delivery, based on technical excellence and deep market insights. We deal with today’s challenges, but also keep a fairer, better tomorrow in sight, looking at how we deliver clean growth, support radical changes in our economy and meet the needs of future communities. Stantec provides equal employment opportunities to all qualified employees and applicants for future and current employment and prohibit discrimination on the grounds of race, colour, religion, sex, national origin, age, marital status, genetic information, disability, sexual orientation, gender identity or gender expression. We prohibit discrimination in decisions concerning recruitment, hiring, referral, promotion, compensation, fringe benefits, job training, terminations or any other condition of employment. Stantec is in compliance with laws and regulations and ensures equitable opportunities in all aspects of employment. Building an inspired, inclusive work environment that attracts, supports, and develops world-class talent is a crucial key to our success. If you are excited by this role but worry that your experience doesn’t exactly align, we encourage you to apply. - Senior Civil Engineer (6463)
Senior Civil Engineer (6463)
The Opportunity
Following a number of successful frameworks bids across the water industry, and in preparation for the most challenging AMP ever, we are expanding our high-performing engineering teams across the country. In Newcastle, we are excited to have been appointed as a Strategic Technical Partner by Northumbrian Water for the AMP8 period. Stantec provide a range of technical enabling, solution delivery and design services to support Northumbrian Water in achieving its vision to be the leading provider of sustainable water and wastewater services. As part of our long-standing relationship with Northumbrian Water, including the ongoing ESH-Stantec joint venture, we will continue to develop innovative solutions to support their delivery of capital investment across both infrastructure & non-infrastructure projects. In order to continue providing our clients with our expert service, we are looking to recruit a Senior Civil Engineer into our team Newcastle on the picturesque Quayside. You will become part of an international team, redefining our landscape with sustainability, the environment and the communities we serve at the heart of everything we do. As a Senior Civil Engineer, you will work across the entire project lifecycle in asset planning, strategy, concept design, outline design & detailed design. You’ll be responsible for delivering civil engineering solutions, guided by our Principal Engineers & Design Leads, whilst also supporting & mentoring our more junior engineers.You can find out more about our work in the water sector here: Stantec H2O+U - UK.
About You
We are interested in speaking with passionate engineers with design experience within the UK water industry. You’ll hold a degree in Civil Engineering and ideally have achieved Chartered status with a relevant professional body such as ICE or CIWEM. You will have gained experienced delivering community focused projects, whilst working collaboratively with multi-disciplinary teams to delivery innovative solutions. We will support your growth & development through training & project exposure, though prior experience within storm overflows, SUDS, surface water management & sewage treatment would be beneficial.
About Stantec
The Stantec community unites more than 31,000 employees working in over 450 locations across 6 continents. We have been working with our clients and communities in the UK for over 150 years. We plan, design, deliver and manage the development and infrastructure needed to support the creation of sustainable, healthy and prosperous communities. Our teams provide effective and relevant solutions, translating our clients’ vision into valued consents, deliverable plans for projects and programmes, and efficient designs for delivery, based on technical excellence and deep market insights. We deal with today’s challenges, but also keep a fairer, better tomorrow in sight, looking at how we deliver clean growth, support radical changes in our economy and meet the needs of future communities. Stantec provides equal employment opportunities to all qualified employees and applicants for future and current employment and prohibit discrimination on the grounds of race, colour, religion, sex, national origin, age, marital status, genetic information, disability, sexual orientation, gender identity or gender expression. We prohibit discrimination in decisions concerning recruitment, hiring, referral, promotion, compensation, fringe benefits, job training, terminations or any other condition of employment. Stantec is in compliance with laws and regulations and ensures equitable opportunities in all aspects of employment. Building an inspired, inclusive work environment that attracts, supports, and develops world-class talent is a crucial key to our success. If you are excited by this role but worry that your experience doesn’t exactly align, we encourage you to apply.